konfigurasi 2 router dengan serial DCE DTE

Berikut ini adalah gambar topologi jaringan dari hasil setting router static :

Disini saya mengunakan Router 0 dan Router 1, berikut setelah kita berhasil masuk CLI dari cisco 

menggunakan host dengan kabel console :

   "*Router 0   

  --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: 

% Please answer 'yes' or 'no'.

pilih saja no 

Router>enable

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#interface serial 2/0

Router(config-if)#ip address 10.1.10.1 255.255.255.0

Router(config-if)#clock rate 9600

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial2/0, changed state to down

Router(config-if)#exit

Router(config)#interface fastEthernet0/0

Router(config-if)#ip address 192.168.2.1 255.255.255.0

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#interface fastEthernet1/0

Router(config-if)#ip address 192.168.3.1 255.255.255.0

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

   "*Router 1

Router>enable

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#interface serial 3/0

Router(config-if)#ip address 10.1.10.2 255.255.255.0

Router(config-if)#clock rate 9600

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial3/0, changed state to up

Router(config-if)#exit

Router(config)#interface fastEthernet0/0

Router(config-if)#ip address 192.168.1.1 255.255.255.0

Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

Cara setting Routing:

  "*Router 0   

Router#configure Terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#ip route 192.168.1.0 255.255.255.0 10.1.10.2

Router(config)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

  "*Router 1

Router#configure Terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#ip route 192.168.1.0 255.255.255.0 10.1.10.2

Router(config)#^Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

Berikut adalah gambar dari hasil ping antar network :

Hasil Ping dari Net 192.168.1.1 ke Net 192.168.2.1 dan 192.168.3.1

Hasil Ping dari Net 192.168.2.1 ke Net 192.168.3.1